I want to know how to connect to my N600. I replaced the old N600 with a Nighthawk R7000. Now I need the N600 to become an access point. The problem is that I cannot connect to my N600. I need the Nighthawk to be my primary router to provice wireless internet. I connected my N600 to my computer and

Unplug the computer you used to configure the AP and plug it back into one of your LAN router's switch ports. Now take an Ethernet cable, plug one end into another unused router switch port and the other end into one of the AP's LAN ports. Performing the Conversion In addition to changing general settings, turning a wireless router into an access point consists of disabling its DHCP server and hooking it up to the new router correctly. Start by configuring the general settings. Go to Advanced > Operation Mode, select Access Point and click Save. Log in to the router via http://tplinkwifi.net after the router reboots. 4. Go to Quick Setup or Settings > Wireless > Wireless Settings and set the SSIDs and passwords for the wireless network. Step 1: With the router plugged into the power supply, hold the Reset button located on the bottom of the router for 30 seconds. Your router will reset, and this is normal. Keep holding the button Jul 05, 2016 · Read more: http://cnet.co/29l1EFd CNET Dong Ngo shows how you can turn that old Wi-Fi router into an external access point and make Wi-Fi sexy. Really sexy.

Jul 05, 2019 · However, the access point router needs an Ethernet cable to connect to the parent modem or router. And it is this cable helps transform the wired signal into a wireless one.

Apr 28, 2017 · We will show you how to turn a Linksys SmartWiFi Router into an Access Point. You have to change this router to become an Access Point if you wish to connect it to CUJO in "Bridge mode". Router as Access Point. At this point don't connect your CUJO to your Network just yet, and follow steps below: 1) Login to your Linksys SmartWiFi Router by I want to turn the router into an access point and basically stop everything else on there as I have a firewall which I want to use, this established my ADSL connection but it lacks the access point. Before I go out and buy an access point, is it possible to disable most of the features in the current plusnet router and have it pass through Set the ‘access point’ IP address to an address on the subnet of your LAN e.g. 192.168.1.200, disable DHCP then click apply (in the LAN Settings page), 3. Connect nothing to the WAN (Internet) port, connect by cable from a LAN port of the ‘access point’ to a LAN port of the router. 4. I followed Easton's instructions and turned my D-link DIR-655 wireless router into a pure Wireless Access Point (WAP) that is connected to DGL-4100 gamer lounge gigabit wired router. I did this in one pass under 5 minutes by connecting my laptop to a LAN (not the WAN) port on the DIR-655 and calling up 182.168.0.1 using Firefox.

Set the ‘access point’ IP address to an address on the subnet of your LAN e.g. 192.168.1.200, disable DHCP then click apply (in the LAN Settings page), 3. Connect nothing to the WAN (Internet) port, connect by cable from a LAN port of the ‘access point’ to a LAN port of the router. 4.

Performing the Conversion In addition to changing general settings, turning a wireless router into an access point consists of disabling its DHCP server and hooking it up to the new router correctly. Start by configuring the general settings. Go to Advanced > Operation Mode, select Access Point and click Save. Log in to the router via http://tplinkwifi.net after the router reboots. 4. Go to Quick Setup or Settings > Wireless > Wireless Settings and set the SSIDs and passwords for the wireless network. Step 1: With the router plugged into the power supply, hold the Reset button located on the bottom of the router for 30 seconds. Your router will reset, and this is normal. Keep holding the button Jul 05, 2016 · Read more: http://cnet.co/29l1EFd CNET Dong Ngo shows how you can turn that old Wi-Fi router into an external access point and make Wi-Fi sexy. Really sexy.